Essential Guide of Trailer Hubs Spindles – September 2021 Edition

Looking to find the best Trailer Hubs Spindles?

We researched 29 Trailer Hubs Spindles, tested 16, and we have done 18 hours of research. The best Trailer Hubs Spindles doesn’t have to be complicated to be great. Our first pick is exactly that. No more, no less. It also costs less than any other products we tested.

The best

No. 1
The ROP Shop (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Replacement (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information
  • Includes - (2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap; comes as shown in the first image
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles"

Intro

Here’s your guide to choosing the best Trailer Hubs Spindles. As there is a great number of models with varying prices, you may find it difficult to figure out which one is right for you. For this reason, we decided to make a top 10 of the Trailer Hubs Spindles of different brands and prices based on the best value for money. This ranking was created to help you find the best Trailer Hubs Spindles depending on your needs and budgets. Our selection criteria are provided to give you a complete picture of the items offered. Get ready to find the Trailer Hubs Spindles that’s right for you!

Our picks

No. 1
The ROP Shop (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Replacement (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information
  • Includes - (2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap; comes as shown in the first image
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles"
No. 2
SOUTHWEST WHEEL 2,000 lbs Trailer Axle Spindle with 5-4.5" Bolt Circle Hub
  • 1 1/4" Diameter, 3 3/8" long shaft, BT8 1" spindle.
  • Spindle includes spindle nut, spindle washer, and cotter pin.
  • 5-4.5" BT8 hub pre raced and studded.
  • Hub includes inner and outer bearing L44643, seal, grease cap, and lug nuts.
  • Rated at 1000 lbs. per spindle, two will hold 2,000 lbs.
SaleNo. 3
LIBRA Set of 2 Trailer Idler Hub Kits 5 on 4.5 for 2000 lbs Axle 1-1/16" Bearings - 22016K
  • Set of 2 New trailer idler hub kits 5 on 4.5 for 2,000 lbs trailer axle, for 1-1/16" straight spindle
  • Bolt pattern: 5 on 4.5", bearing races and 1/2"-20 studs installed
  • Kits also includ: 4x L44649 outer cone bearings, 2x Grease seals 1-1/16", 2x E Z lube grease caps with rubber plug; 10 cone wheel nuts 1/2"-20 thread
  • pls noted, this hub fit straight spindles, not for tapered spindles

Why you should trust us

This guide represents more than 10 years of experience in researching, testing, and writing about many subject. Our people are experts in all of their fields.
We alors spent 18 hours reading any article we could find on the internet and all the customer reviews at various retailer sites such as those of Amazon, Home Depot or Wallmart. We found many website that was a valuable resource with involved buying guides and detailed Trailer Hubs Spindles information.
As for me, I’m very familiar with the Trailer Hubs Spindles since I got it from 5 years.

Top 10

No. 1
The ROP Shop (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Replacement (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information
  • Includes - (2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap; comes as shown in the first image
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles"
No. 2
SOUTHWEST WHEEL 2,000 lbs Trailer Axle Spindle with 5-4.5" Bolt Circle Hub
  • 1 1/4" Diameter, 3 3/8" long shaft, BT8 1" spindle.
  • Spindle includes spindle nut, spindle washer, and cotter pin.
  • 5-4.5" BT8 hub pre raced and studded.
  • Hub includes inner and outer bearing L44643, seal, grease cap, and lug nuts.
  • Rated at 1000 lbs. per spindle, two will hold 2,000 lbs.
SaleNo. 3
LIBRA Set of 2 Trailer Idler Hub Kits 5 on 4.5 for 2000 lbs Axle 1-1/16" Bearings - 22016K
  • Set of 2 New trailer idler hub kits 5 on 4.5 for 2,000 lbs trailer axle, for 1-1/16" straight spindle
  • Bolt pattern: 5 on 4.5", bearing races and 1/2"-20 studs installed
  • Kits also includ: 4x L44649 outer cone bearings, 2x Grease seals 1-1/16", 2x E Z lube grease caps with rubber plug; 10 cone wheel nuts 1/2"-20 thread
  • pls noted, this hub fit straight spindles, not for tapered spindles
No. 4
SOUTHWEST WHEEL 5-Hole, 4.5" Bolt Circle Idler Hub for 2,000 lb. Axles (BT8 Spindle) 1" Spindle
  • 5 studs 4.5" bolt circle using L44643 inner and outer bearings.
  • Contains TruRyde inner bearing, outer bearing, seal, grease cap and lug nuts.
  • Fits a BT8 Spindle (1" OD) - Will not work on 1 1/16" spindle or some marine trailer axles.
  • TruRyde hubs are pre-raced & all studs are 1/2"-20 with yellow finished zinc plating.
  • TruRyde parts are manufactured to automotive standard in ISO/TS-16949 registered factory.
No. 5
Rigid Hitch Pair of 4-Bolt On 4 Inch Hub Assembly (AKSQ-220044) Includes (2) Square Shaft 1-1/16 Inch Straight Spindles & Bearings
  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins.
  • Bearings included - (4) L-44649 1-1/16" inside dimension
  • Hubs have pre-installed pressed in races
  • Hub has a 4-bolt pattern on 4" bolt circle. Pilot diameter 2-1/2", flange diameter 5.56" and measures 4-1/4" tall (through center of hub)
  • Spindles feature a SQUARE 1-1/2" stock diameter with a bearing surface of 1-1/16 inch.
No. 6
SOUTHWEST WHEEL 2,000 lbs Trailer Axle Spindle with 4-4" Bolt Circle Hub
  • 1 1/4" Diameter, 3 3/8" long shaft, BT8 1" spindle.
  • Spindle includes spindle nut, spindle washer, and cotter pin.
  • 4-4" BT8 hub pre raced and studded.
  • Hub includes inner and outer bearing L44643, seal, grease cap, and lug nuts.
  • Rated at 1000 lbs. per spindle, two will hold 2,000 lbs.
No. 7
Trailer Hub Spindle Nut Washer Kit
  • 2 6-Slot Spindle Nuts 1"-14
  • 2 1" D Washer2
  • 2 1" Tang Washers
No. 8
Rigid Hitch Pair of 5-Bolt On 4-1/2 Inch Hub Assembly (AKRD-2200545) Includes (2) 1-1/16 Inch Straight Spindles & Bearings
  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins.
  • Bearings included - (4) L-44649 1-1/16" inside dimension.
  • Hubs have pre-installed pressed in races.
  • Hub has a 5-bolt pattern on 4-1/2" bolt circle. Pilot diameter 2-1/2", flange diameter 5.56" and measures 4-1/4" tall (through center of hub)
  • Spindles feature a ROUND 1-1/4" stock diameter with a bearing surface of 1-1/16 inch.
SaleNo. 9
Rigid Hitch Trailer Hub Kit - for 1-3/8" Inner / 1-1/16" Outer Tapered Spindle - 5 Bolt on 4-1/2" Bolt Circle
  • Fits 3,500 lb. axles
  • Complete assembly with bearings, seal, dust cap, cotter pin and lug nuts
  • Capacity 1,750 lbs
  • Thread 1/2"-20, 5 Bolt on 4-1/2" Bolt Circle
  • Read product description below for more information
No. 10
Rigid Hitch Pair of 5-Bolt on 5 Inch Hub Assembly (AKSQ-350055) Includes (2) Square Stock 1-3/8 Inch to 1-1/16 Inch Tapered Spindles & Bearings
  • Pair of 1-3/8" to 1-1/16" tapered spindles.
  • Bearings included - (2) L-68149 1-3/8" I.D & (2) L-44649 1-1/16" I.D
  • Hubs have pre-installed pressed in races.
  • Hub has a 5-bolt pattern on 5" bolt circle. Pilot diameter 2.59", flange diameter 6-1/2" and measures 4-1/4" tall (through center of hub)
  • Spindles feature a SQUARE 1-3/4" stock diameter with a tapered spindle surface of 1-3/8" & 1-1/16"

How we tested

We search all the field to find the best Trailer Hubs Spindles and all the type for it and get the best alternatives, priced decently, and easy to use. After that we tested all the main parameters we use : These things can separate the great Trailer Hubs Spindles from the good.

  • Easy To use
  • Options
  • Quality
  • Longevity

How we picked

We search for all the field to find the best Trailer Hubs Spindles and all the type for it and get the best alternatives, priced decently, and easy to use.
The main parameters we use : These things can separate the bad Trailer Hubs Spindles from the good.

  • Price
  • Easy To use
  • Customer reviews
  • Quality
  • Longevity
  • Dimensions

Current Offers

SaleNo. 1
LIBRA Set of 2 Trailer Idler Hub Kits 5 on 4.5 for 2000 lbs Axle 1-1/16" Bearings - 22016K
  • Set of 2 New trailer idler hub kits 5 on 4.5 for 2,000 lbs trailer axle, for 1-1/16" straight spindle
  • Bolt pattern: 5 on 4.5", bearing races and 1/2"-20 studs installed
  • Kits also includ: 4x L44649 outer cone bearings, 2x Grease seals 1-1/16", 2x E Z lube grease caps with rubber plug; 10 cone wheel nuts 1/2"-20 thread
  • pls noted, this hub fit straight spindles, not for tapered spindles
SaleNo. 2
Rigid Hitch Trailer Hub Kit (BT-100-04-A) 4 Bolt on 4 Inch Circle - 1 inch I.D. Bearings
  • Fits 2,000 lb. axles with 1" straight spindle
  • Complete assembly with bearings, seal, dust cap, cotter pin and lug nuts
  • Measures 4-1/4 inches tall (through center of hub)
  • 2,000 lb capacity - 1/2-20 thread - 4 bolt on 4 inch bolt circle
  • Read product description below for more information

Conclusion

This guide is here to support you in your choice of Trailer Hubs Spindles and is regularly updated so that you can make an informed selection. Nowadays, it’s not that easy to know about each and every product that’s on the market. So we hope that this comparison was able to help you with choosing the best Trailer Hubs Spindles according to your criteria. Your comments are most welcome and they will help us improve the ranking.

Click to rate this post!
[Total: 0 Average: 0]

Last update on 2021-09-20 at 10:24 / Affiliate links / Images from Amazon Product Advertising API

Leave a Comment